Re: MMS1 & 2 for lyme caused pain in root canals

[Guest guest]

Hello Jen,

We have had remarkable results using a variation of the mouthwash formula. The

standard mouthwash has a concentration in the 800 - 1000 PPM available chlorine

dioxide range. In dealing with infected teeth, we used the same mouthwash, but

lowered the PH of the solution to 6. This gives a small amount of free chlorine

dioxide that penetrates the gums to deal with the infections in the roots of the

teeth.

We would mix a fresh solution every week and found that 250 ml would last about

a week.

This study was done in conjunction with a Dentist, who is interested in the

process. The tooth was scheduled for extraction and to be replaced with an

implant. We delayed the implant procedure to see if the mouthwash could knock

the infection down. It only took 2 days to totally clear up the infection, and

we continued to monitor for 2 weeks. The initial application was done by the

Dentist with the idea to get the solution as far down along the gum/tooth

interface as possible. Following that, the application was done as a normal

mouthwash twice a day.

We started with gum pain and an infection, in 2 days the pain and infection were

gone, and 2 weeks later there was no reoccurrence of the pain or infection. At

that time the tooth was pulled and the implant installed. When the tooth was

extracted, there was no indication of infection.

In addition we have had several other cases where a crown with a post has

started to come loose allowing for infection to set into the socket. The

slightly activated solution quickly eliminated the infection, and the continued

use of the normal mouthwash kept everything clear until the tooth could be

repaired.

I would not recommend using bleach (hypochlorous acid) in the mouth.

Tom

>

> What about pain caused by lyme & other anarobic bacteria living inside the 400

tubes of root canal? Will MMS1 & MMS2  eradicate the bugs inside the root

canals?   Pls. advise.  Thanks.

>  

> jen  -

>

[Guest guest]

Hi Tom,Can you describe pls. the steps to prepare the solution you successfully employed with the dentist using MMS1? Or maybe there is a link somewhere where this is already described.I noticed many times you mention "mix x% sodium chlorite with y ml of water". I think for this group it would be much helpfull to describe the quantities using MMS1 (as most of the people buying MMS have 22.5% sodium chlorite - MMS is this basically).I hope I'm not asking too much :)Thanks in advance,DacianFrom: silverfox_science <poast@...>Subject: [ ] Re: MMS1 & 2 for lyme caused pain in root

canals Date: Thursday, September 23, 2010, 6:55 AM

Hello Jen,

We have had remarkable results using a variation of the mouthwash formula. The standard mouthwash has a concentration in the 800 - 1000 PPM available chlorine dioxide range. In dealing with infected teeth, we used the same mouthwash, but lowered the PH of the solution to 6. This gives a small amount of free chlorine dioxide that penetrates the gums to deal with the infections in the roots of the teeth.

We would mix a fresh solution every week and found that 250 ml would last about a week.

This study was done in conjunction with a Dentist, who is interested in the process. The tooth was scheduled for extraction and to be replaced with an implant. We delayed the implant procedure to see if the mouthwash could knock the infection down. It only took 2 days to totally clear up the infection, and we continued to monitor for 2 weeks. The initial application was done by the Dentist with the idea to get the solution as far down along the gum/tooth interface as possible. Following that, the application was done as a normal mouthwash twice a day.

We started with gum pain and an infection, in 2 days the pain and infection were gone, and 2 weeks later there was no reoccurrence of the pain or infection. At that time the tooth was pulled and the implant installed. When the tooth was extracted, there was no indication of infection.

In addition we have had several other cases where a crown with a post has started to come loose allowing for infection to set into the socket. The slightly activated solution quickly eliminated the infection, and the continued use of the normal mouthwash kept everything clear until the tooth could be repaired.

I would not recommend using bleach (hypochlorous acid) in the mouth.

Tom

>

> What about pain caused by lyme & other anarobic bacteria living inside the 400 tubes of root canal? Will MMS1 & MMS2 eradicate the bugs inside the root canals? Pls. advise. Thanks.

>

> jen -

>

[Guest guest]

Hello Dacian,

The 22.4% concentration of sodium chlorite is dangerous to handle. I recommend

diluting it down to a 5% concentration for general use.

Let's start with making a 5% concentration. Put 22.3 ml of 22.4% sodium

chlorite into a measuring device and add enough distilled water to make a total

of 100 ml. You now have 100 ml of 5% sodium chlorite.

The general mouthwash is made by putting 16 ml of 5% sodium chlorite into a

bottle and add enough water to make a total of 500 ml.

The slightly activated mouthwash was made by putting 240 ml of water into a

container and adding citric acid to it while monitoring with a PH meter. When

the PH reached 6 we stopped. I was using 2.5% citric acid and don't have a good

idea of how much was added, but it wasn't very much. The amount needed will

vary depending upon the PH of the water you are starting with. The goal is to

end up with water that has a PH of 6.

Once we had 240 ml of PH 6 water, I added 8 ml of 5% sodium chlorite, then added

water to bring the total up to 250 ml. This solution takes a few hours to

activate, so it was mixed up ahead of time. In general you would mix it up the

night before you want to use it.

Tom

>

> Hi Tom,

>

> Can you describe pls. the steps to prepare the solution you successfully

employed with the dentist using MMS1? Or maybe there is a link somewhere where

this is already described.

>

> I noticed many times you mention " mix x% sodium chlorite with y ml of water " .

I think for this group it would be much helpfull to describe the quantities

using MMS1 (as most of the people buying MMS have 22.5% sodium chlorite - MMS is

this basically).

>

> I hope I'm not asking too much

>

> Thanks in advance,

> Dacian

>