Re: Pete Re: focus not connecting

[Guest guest]

Ideally you will have a cable that indicates it uses the " Prolific chipset " . There are lots of Serial/USB convertors, but the Focus sends a lot more information a lot faster than most other devices that use the serial port. The Prolific chipset is very fast and, in my experience, has always worked. There are other options that state transfer rates of 1Mbps or faster and have relatively large caches. These may work if you can't find one with the Prolific chipset.

Pete-- Van Deusenpvdtlc@...http://www.brain-trainer.com305/433-3160The Learning Curve, Inc.

Hi Pete

I managed to get the Hasp to work as I read a posting on the BE forum.

Basically, I installed the BE, and then tried to open, but it would

not due to the Hasp. I thought I had to do these steps before I

downloaded the newest version of BE.

But, I downloaded it anyway..version 1.5 (I don't know if this is

designed for Vista based on your site saying 1.4 is for Vista)

After downloading 1.5..it worked.

As far as the snyc error. I am going to recharge the battery and see

if that works.

I purchased the cables unlimited 2.0 to RS232 serial adapter.

http://www.cablesunlimited.com/products/Prod_Individual3.aspx?

groupcode=I3274

I went with this one as it was the only one I could find that says it

works with Vista 64.

thanks

Barbra

[Guest guest]

I know than many of the computer/electronics stores around here do not know what chip set is in their adapters.  Here are three web sites that carry themhttp://tekgems.com/Products/tg-bt-usb-gmus-03.htmhttp://www.usbgear.com/USB-PRODUCT-DETAILS.cfm?sku=Y-105A & catid= & cats=http://www.beaglesoft.com/232usb.htm georgemartin@...www.northstarneurofeedback.com Ideally you will have a cable that indicates it uses the "Prolific chipset".  There are lots of Serial/USB convertors, but the Focus sends a lot more information a lot faster than most other devices that use the serial port.  The Prolific chipset is very fast and, in my experience, has always worked.  There are other options that state transfer rates of 1Mbps or faster and have relatively large caches.  These may work if you can't find one with the Prolific chipset.Pete-- Van Deusenpvdtlc@...http://www.brain-trainer.com305/433-3160The Learning Curve, Inc.On Sun, Dec 14, 2008 at 4:20 PM, fatcat8dog  wrote:Hi PeteI managed to get the Hasp to work as I read a posting on the BE forum.Basically, I installed the BE, and then tried to open, but it would not due to the Hasp. I thought I had to do these steps before I downloaded the newest version of BE.But, I downloaded it anyway..version 1.5 (I don't know if this is designed for Vista based on your site saying 1.4 is for Vista)After downloading 1.5..it worked.As far as the snyc error. I am going to recharge the battery and see if that works.I purchased the cables unlimited 2.0 to RS232 serial adapter.http://www.cablesunlimited.com/products/Prod_Individual3.aspx?groupcode=I3274I went with this one as it was the only one I could find that says it works with Vista 64.thanksBarbra

--- Get FREE High Speed Internet from USFamily.Net! ---

[Guest guest]

I bought this, very cheap (8.99euro) and working good, but I have Win XP O.S.http://www.nierle3.com/en/article/4692/USB_to_Serial_Converter_with_25-pin-adapter.htmlNot sure if it has Vista driver.Regards, ilarioDe: fatcat8dog Para: braintrainer Enviado: domingo, 14 de diciembre, 2008 19:20:09Asunto: Pete Re: focus not connecting

Hi Pete

I managed to get the Hasp to work as I read a posting on the BE forum.

Basically, I installed the BE, and then tried to open, but it would

not due to the Hasp. I thought I had to do these steps before I

downloaded the newest version of BE.

But, I downloaded it anyway..version 1.5 (I don't know if this is

designed for Vista based on your site saying 1.4 is for Vista)

After downloading 1.5..it worked.

As far as the snyc error. I am going to recharge the battery and see

if that works.

I purchased the cables unlimited 2.0 to RS232 serial adapter.

http://www.cablesun limited.com/ products/ Prod_Individual3 .aspx?

groupcode=I3274

I went with this one as it was the only one I could find that says it

works with Vista 64.

thanks

Barbra

>

> > Hi

> > I finally got my BE to open, and the Hasp to be reconized by my

vista.

> > I followed the steps to install the focus. However, when BE is

trying

> > to connect to the focus it flashes between connected and

connecting

> > with an error flashing next to it "sync error"

> >

>

[Guest guest]

I bought this, very cheap (8.99euro) and working good, but I have Win XP O.S.http://www.nierle3.com/en/article/4692/USB_to_Serial_Converter_with_25-pin-adapter.htmlNot sure if it has Vista driver.Regards, ilarioDe: fatcat8dog Para: braintrainer Enviado: domingo, 14 de diciembre, 2008 19:20:09Asunto: Pete Re: focus not connecting

Hi Pete

I managed to get the Hasp to work as I read a posting on the BE forum.

Basically, I installed the BE, and then tried to open, but it would

not due to the Hasp. I thought I had to do these steps before I

downloaded the newest version of BE.

But, I downloaded it anyway..version 1.5 (I don't know if this is

designed for Vista based on your site saying 1.4 is for Vista)

After downloading 1.5..it worked.

As far as the snyc error. I am going to recharge the battery and see

if that works.

I purchased the cables unlimited 2.0 to RS232 serial adapter.

http://www.cablesun limited.com/ products/ Prod_Individual3 .aspx?

groupcode=I3274

I went with this one as it was the only one I could find that says it

works with Vista 64.

thanks

Barbra

>

> > Hi

> > I finally got my BE to open, and the Hasp to be reconized by my

vista.

> > I followed the steps to install the focus. However, when BE is

trying

> > to connect to the focus it flashes between connected and

connecting

> > with an error flashing next to it "sync error"

> >

>